Microsens Media Converter/Signal Repeater Module Manual de usuario descargar pdf (Pagina 25)

Media Converter/Signal Repeater page 25/29

OID Name Access Description

1.3.6.1.4.1.20044.21.2.3.2.26.15 ms430580mAlmLine2RxPwrLowAla r TRSCV 2 Rx Power Low: Alarm

indicating that the transceiver input

power of Line 2 is lower than the

threshold value written in the

transceiver EEPROM

1.3.6.1.4.1.20044.21.2.3.2.26.16 ms430580mAlmLine2RxPwrHighAla r TRSCV 2 Rx Power High: Alarm

indicating that the transceiver input

power of Line 2 is higher than the

threshold value written in the

transceiver EEPROM

1.3.6.1.4.1.20044.21.2.3.3 ms430580mAlmLineCrit

1.3.6.1.4.1.20044.21.2.3.3.7 ms430580mAlmsynthAlm7

1.3.6.1.4.1.20044.21.2.3.3.7.1 ms430580mAlmLine2TrscvAbsent r Line 2 SFP not plugged: This OID

indicates that the transceiver

module 2 is not present.

1.3.6.1.4.1.20044.21.2.3.3.7.2 ms430580mAlmLine2TrscvDdmAbsent r DDM supported on Line 2 SFP: This

OID indicates that the transceiver

module 2 does not support Digital

Diagnostic Monitoring Functions

1.3.6.1.4.1.20044.21.2.3.3.7.4 ms430580mAlmLine2HwFail r Line 2 HW Failure: This OID indicates

a hardware failure on the Line 2

1.3.6.1.4.1.20044.21.2.3.3.7.5 ms430580mAlmLine2TrscvLsd r Line 2 SFP optical TX ON :This OID

indicates the optical output power

is off on Line 2

1.3.6.1.4.1.20044.21.2.3.3.7.9 ms430580mAlmLine2TrscvDdmWarning r Warning DDM on Optical Module 2:

This OID indicates a warning is

present coming out of optical

interface DDM on Line 2

1.3.6.1.4.1.20044.21.2.3.3.7.10 ms430580mAlmLine2TrscvDdmAlm r Alarm DDM on Optical Module 2:

This OID indicates an alarm is

present coming out of optical

interface DDM on Line 2

1.3.6.1.4.1.20044.21.2.3.3.7.12 ms430580mAlmLine2Fail r Line 2 Failure: This OID indicates a

failure on the Line 2

1.3.6.1.4.1.20044.21.2.3.3.24 ms430580mAlmline2AccessioAlm

1.3.6.1.4.1.20044.21.2.3.3.24.1 ms430580mAlmLine2LasFail r Line 2 SFP Tx Failed :This OID

indicates that the transmitter fails

for the transceiver plugged into the

Line 1 (this alarm reports the

transmitter failure alarm generated

by the transceivers)

1.3.6.1.4.1.20044.21.2.3.3.24.4 ms430580mAlmLine2Los r Loss of Optical signal on Line 2 :This

OID indicates that no signal is

present on the transceiver 2

1.3.6.1.4.1.20044.21.3 ms430580mmeasures

1.3.6.1.4.1.20044.21.3.1 ms430580mMesrOther

1.3.6.1.4.1.20044.21.3.2 ms430580mMesrClient

1.3.6.1.4.1.20044.21.3.2.16 ms430580mMesrline1Temperature r Line 1 SFP Temperature :This OID

gives the temperature of the

transceiver Line 1, read from the

DDM (Digital Diagnostic

Monitoring) (Unit = °C)

1.3.6.1.4.1.20044.21.3.2.17 ms430580mMesrline1Volt r Line 1 SFP Power Supply: This OID

gives the voltage of the transceiver

Line 1, read from the DDM (Digital

Diagnostic Monitoring) (Unit = V)

MICROSENS GmbH & Co. KG - Küferstraße 16 - 59067 Hamm - Tel. +49 2381/9452 0 - Fax 9452 100 - www.microsens.com

1 2 ... 20 21 22 23 24 25 26 27 28 29

Comentarios a estos manuales

Sin comentarios

Microsens Media Converter/Signal Repeater Module Manual de usuario Pagina 25

Comentarios a estos manuales